This page was translated from the original Japanese by AI. Read the original article in Japanese

How to Refill Loose Powder: Pouring from a Pouch and Replacing the Sifter

Where to check the labels on the refill pouch and the bottom of the loose powder case

When refilling loose powder, empty the case first and identify the removable sifter and the pouch opening. Hold the opening close to the case and pour a little at a time. When you finish, check for powder on the rim before replacing the sifter. If the lid won’t close, see where it catches. You may be able to fix it before tipping the case to start over.

This guide covers loose powder poured from a pouch into its matching case. Refills that come in a pressed pan or slide in as a cartridge follow different steps. Even if the cases look alike, follow your product’s directions on whether to shake the pouch, wipe the case, or dispense the powder a certain way after replacing the sifter.

1. Check that the refill fits, then empty the case

Where to check the labels on the refill pouch and the bottom of the loose powder case

Before opening the pouch, check the product name and model on the underside of the case or on the original box. Compare them with the compatible products listed on the refill. Even if the shade name matches, the sifter shape or capacity may differ. Check more than the capacity. If the product comes in several sizes under the same name, confirm which size the refill is for.

If the directions say to use up the powder before refilling, leave the pouch sealed until the old powder is gone. If you can still see some at the bottom, check whether you can dispense it through the sifter as you normally would. There’s no need to turn a case that still contains powder upside down just to see if it is empty. Avoid mixing a different shade or another powder into what is left and estimating the amount by eye.

Lay a sheet of paper on a flat, dry surface. Pick a spot where the entire case can sit securely, away from windows, drafts, and humidifiers. Decide where to set the outer lid, puff, and sifter ahead of time so you won’t need to reach across the open container as often. If the pouch directions call for scissors, have them nearby before opening it.

2. Grip the part shown in the directions and remove the sifter

Holding the case steady while lifting the tab on the rim of a perforated sifter

Remove the outer lid and set the puff aside to expose the perforations or mesh that the powder passes through. With the case on the work surface, look for the tab or edge shown in the directions. Where you can safely apply pressure differs between a rigid perforated plate and soft mesh. If you can’t find where it comes off, compare the diagram with the case before pressing the center or inserting a tool into a hole.

If the directions say to lift the sifter, steady the case with one hand and lift it by the indicated edge. If it won’t budge without force, check whether there is another part to remove or a specific sequence for releasing the lock. Set the sifter next to the case so you can remember which way it goes back. If it has an alignment mark, look for the matching spot on the case while it is apart.

A tab on the removed sifter and its matching notch on the case rim

If powder remains on the rim or inside the case, check the product’s cleaning instructions. A washable puff does not necessarily mean the case and sifter can be washed with water. Wait until the recommended cleaning and drying are complete before opening the pouch, so new powder doesn’t go into a damp case. If the mesh normally moves or you’re unsure what the tray does, see our guide to telling the mesh from the inner lid in a face powder case.

3. Hold the pouch close to the case and pour gradually

Holding the refill pouch opening close to the inside of the case to transfer powder gradually

If the directions say to shake the pouch, do so while it is still sealed. Then find the opening point and avoid tearing it open abruptly if powder has gathered there. Open it as the directions indicate. Cutting the pouch all the way across at the outset because the powder seems hard to pour can make it spill out over a wide area when you tilt it.

Leave the case on the work surface, hold the pouch lightly, and bring its opening close to the case opening. Tilt the pouch slowly from an angle that lets you see where the powder falls. If the opening is outside the rim, bring the pouch upright before repositioning it. If the flow stops, set it upright and look for a fold at the opening. That will tell you more about what to do next than tapping the pouch from high above the case.

If powder starts piling up on one side, bring the pouch upright and pause. If the instructions include a step for leveling the surface, put the pouch down, set the case on a level surface, and follow the directions. A mound in one spot doesn’t tell you whether the entire case is full. Check whether powder is covering the ledge where the sifter sits. There’s no need to press the powder down with the sifter to make it all fit.

4. Check the rim and replace the sifter and outer lid

An overhead view of the ledge where the sifter sits in a refilled case

After pouring, look down at the entire rim. If you see powder on the sifter ledge or the threads of the outer lid, remove it using a method suitable for the product. If you noted the sifter’s orientation when you removed it, use that as a guide and check that neither side is sticking up. If the puff has a designated spot, put it there before closing the outer lid.

If the outer lid stops partway, take it off and check where it catches before tightening further. Check whether the mound of powder touches the sifter, whether the sifter is tilted, and whether the puff is in its proper spot. With a screw-on lid, look from the side to check that both edges sit at the same height. This helps you avoid forcing a lid that has gone on crooked.

Uneven gaps on either side of a screw-on lid that sits at an angle

If the pieces still don’t fit after you reassemble them, check whether they match and face the right way. See if you can finish with the case called for in the instructions. Avoid swapping in parts from another case or carrying it around with the outer lid partly open.

5. On the first use, check how a small amount dispenses

A small patch of loose powder on a puff after refilling the case

Once the lid closes, use the case as you normally do and start with a little powder to see how it dispenses. Even if the powder comes through holes, check the label to see whether the case should be turned upside down. When picking it up with a puff, note where it has and hasn’t collected and adjust the amount before applying it. If too much comes out, adjust the powder on the puff as your product directs instead of trying to use it all by spreading it across your cheeks.

If hardly any powder comes out, check that you replaced the sifter correctly and that no protective seal meant to be removed remains on a new part. Before opening up the holes or mesh with a tool, work out whether the problem is with assembly or how you pick up the powder. If too much comes out every time, reconsider how much you move the case each time you dispense it.

Before putting the case away, check that the outer lid is shut and that no powder remains on the outside. If it looks white or powdery in patches after you apply it, see our guide to adjusting the amount of face powder and fixing a powdery finish.

See all articles →