This page was translated from the original Japanese by AI. Read the original article in Japanese

How to Use Brush-On Face Powder: Dispensing Powder and Storing the Brush

Hands removing the cap from a brush-on face powder and lowering the cover

Brush-on face powder comes in a container that dispenses powder into the bristles so you can apply it directly to your face. Sometimes nothing comes out after you remove the cap, or the first stroke looks white. Before trying again and again on your face, separate the step of dispensing the powder from the step of checking whether it came out. That makes it easier to see what to adjust.

This guide covers loose powder that comes out through the brush tip and has a sliding cover around the bristles. Some products call for shaking the container, while others call for gently tapping the brush. Check the directions for the one you have, then work through the steps from first use to putting it away.

1. Remove the cap and lower the brush cover

Hands removing the cap from a brush-on face powder and lowering the cover

First, use the diagram on the box or container to tell the removable cap from the brush cover that slides up and down while attached to the body. If your product calls for lowering the cover for use, hold the body that contains the powder and lower the cover to the indicated position to expose the bristles. The lid at the base opposite the brush is a separate part from the cap you remove here.

Set the removed cap nearby with its opening visible so it is easier to tell it apart from the cover when putting the brush away. If you can see only part of the bristles, look from the side to see whether the cover stopped partway before pulling on the bristles.

Close-up of the removed cylindrical cap and the sliding cover around the bristles

Before using a new product for the first time, check whether removing the cap is enough or whether there is a part to remove once before use. Some products, for example, have a shipping pin in the center of the brush. Compare the location with the diagram for your product before pulling out a part that is not shown in the directions or applying the first-use instructions for another product.

If the cover does not move, check whether the directions say to turn, push, or pull it. Forcing it may leave you gripping the bristles as you reposition your hand. Set the container on a stable surface, identify the part that needs to move, and then try again.

2. Use a tissue to check whether powder has reached the bristles

Hands lightly tapping the tip of the built-in brush against a tissue to dispense powder

First, place a dry tissue on a flat surface. If the instructions say to tap the bristles lightly against a tissue or similar surface, use that method to dispense the powder. If your product calls for shaking the body toward the surface, follow its directions, including how to hold it. In either case, there is no need to press hard enough to make the bristles splay.

Along with counting how many times you tapped or shook it, lift the brush once to see whether powder is visible on the bristles or tissue. A translucent powder, for example, can be hard to see on white tissue. Before assuming nothing came out, look from an angle away from any shadows on the surface.

If powder collects in one spot on the bristles or tissue, adjust the amount before touching the brush to your face. If the directions say to remove excess powder with a tissue, tap lightly on a fresh area so you can distinguish it from the mark already there. Repeating the tap on the same spot makes it harder to tell the powder you just deposited from what fell there before.

A light dusting of powder on a tissue compared with powder collected in one spot

The tissue gives you a rough idea of whether powder is coming out and whether it is clumping in one spot. The amount on the paper does not tell you how much to use for one application or how much you need for sun protection. This guide covers finishing your makeup. For sun protection, follow the directions on your specific product.

3. Apply a thin layer from the center of the face outward

Holding the brush-on container and sweeping face powder from the center of the cheek outward

If your product calls for applying powder from the center of the face outward, start near the center and move the brush so the tips touch the skin lightly. The motion differs depending on whether you are meant to use circles or glide the brush over the skin. If you are holding it far back and the container's weight makes it press down too hard, move your fingers closer to the body below the cover and find a grip that keeps the bristles from splaying too far.

In areas where it is hard to place the whole brush, such as around the sides of the nose, lift it away and change your grip so you can see the tips before touching down again. If the foundation underneath has gathered in one spot, check the base before adding powder. Covering it with powder can make it hard to tell whether the foundation buildup or the amount of powder is affecting the finish.

When moving from a cheek to the forehead, check whether there is enough left on the brush before dispensing more powder for every new area. If only one side of your face looks white, face the mirror straight on and compare both sides in the same light. See how to fix a white cast or a powdery finish from face powder for ways to adjust areas where you applied too much.

4. If little powder comes out, check the opening and the amount left

A face powder container showing the sliding cover and powder left in the clear section

If it looks as though no powder is reaching the bristles, check whether the cover is lowered to the indicated position, whether the first-use setup is complete, and whether any powder is visible in the container. If you cannot see the amount left from the outside, check the method given for your product before opening the container just to look.

Some products direct you to repeat the same setup if little powder comes out either at first or partway through use. If the instructions specify how to remove powder from the bristles or wipe the brush clean, try that method first. Stick to checking the tool and your technique. Keep toothpicks and similar objects out of the powder passage, and keep water out of the container.

When checking the powder again, use a surface away from your face. After changing the shape of the bristles or the position of the cover, check the flow on a fresh area of tissue so you can tell after which step the powder appeared. If working within the directions does not help, read the handling instructions again before taking the container apart.

5. Cover the bristles before closing the cap

Hands raising the cover on a built-in brush with the removed cap set aside

If the product directions say to wipe away powder left inside the cap or on the bristles after use, follow those care instructions. On products that close after the cover is raised, slide it up to the indicated position first to enclose the bristles. If the mechanism clicks when closed, use the sound or the position of the cover as your cue.

Before putting on the cap, look from the side for any bristles caught at the cover's edge. If the cap goes on crooked, remove it and check the position of the cover before pressing it down. If the directions describe wiping with a damp sheet, also check whether they say to let it dry before closing it.

If you are unsure next time, pick one point where you had trouble. If only the first stroke was heavy, look at how the powder settles on the tissue. If powder stopped coming out during use, check the cover position that exposes the bristles or the amount left. If you found powder in your pouch, check the positions of the cover and cap when putting it away. Choosing what to look at lets you troubleshoot before applying it to your face.

See all articles →