On days when you go out in sandals, the tops of your feet can be easy to overlook until you put your shoes on, even if you applied sunscreen to your shins. If you spread it only down the middle, you may notice after putting on your sandals that you also wanted coverage at the base of the toes and on either side of the straps.
Before putting on sandals, apply the labeled amount of a sunscreen suitable for the body to the tops of your feet. Spread it toward the base of the toes and check the edges visible from the side. If you wipe away sweat or go into water while out, reapply where you can take your footwear off.
1. Check what is visible on the tops of your feet when wearing sandals

Set out the sandals you will wear today. If a strap crosses the top of your foot, see if skin is visible on the ankle side as well as the toe side. With several thin straps, look between them too.
If you apply only along the edges of the straps, adjacent skin may show when your foot shifts slightly inside the sandal. Take the sandals off and apply across the top of the foot as one continuous area. If your shins are exposed too, check from the shin side so coverage continues across the front of the ankle.
Twisting your foot makes the edges hard to see. Sit in a chair and place the soles on the floor or a mat. Putting both feet side by side helps you remember to check both. If you switch to shoes that cover the tops of your feet, check what is visible in those shoes, such as the ankles.
2. Choose sunscreen suitable for the body and read the label for the amount and directions

Before applying, check the container or box to see whether your sunscreen can be used on the body. Some milks and gels must be shaken before dispensing or list a suggested amount to spread over the skin. Follow the directions for your own product. The tops of your feet cover a small area, but do not assume one drop is enough for every product.
Before deciding on the amount, look again in front of and behind the sandal strap. You may see skin near the base of the toes in front and skin leading up to the ankle behind it. Taking the sandal off and applying across both areas makes it easier to move your hand than feeling under the strap with a fingertip.

If you only have a spray, also read the instructions on distance and overspray. If directed to spread it by hand, do so after spraying. For application by formula, also see how to use spray sunscreen.
3. Spread from the top of the foot to the base of the toes before putting on sandals

Pat the skin dry and apply with your sandals off. If your product is meant to be spread by hand, take the amount specified on the label, put it on the broad part of the top of the foot, and spread it to the base of the toes. Laying the pads of your fingers against the skin avoids a poking motion with your nails and makes it easier to keep track of how far you have spread it.
Once you cover the center, move your hand to areas you have yet to touch instead of repeating the same stroke. Check the big-toe side, the little-toe side, and the tops of any exposed toes in turn. When applying to the shins as well, join the two application areas at the front of the ankle. Repeat the same sequence on the other foot.
If sunscreen gets on the sole of your foot or the sandal footbed, wipe it off before putting the sandal on so you do not slip. It is easier to reach the area while seated than while standing on one foot to look at it.
4. Check for missed spots on the little-toe side and at the front of the ankle

From directly above, the highest part of the foot is easy to see, but the little-toe edge may fall in shadow. Keep your foot on the floor and look from slightly to the side. If your fingers have not reached an edge visible above your sandals, spread the sunscreen there following your product directions.
The front of the ankle is easy to assume you have covered when you apply separately to the shin and the top of the foot. Think back to whether you moved your fingers from shin to foot or spread the sunscreen back toward the ankle from the foot. With a colorless sunscreen, skin shine alone cannot tell you how much you applied or how much UV protection you have.
There is no need to apply a thicker layer just where the strap crosses. If you see cream collecting in one spot after spreading, blend it into the surrounding area. Check the visible edges first, then finish both feet in the same order to make the routine easier to follow.
5. Reapply as directed after wiping off sweat or going into water

When the tops of your feet will be exposed to sunlight again after you towel off sweat outdoors or go into water, reapply following the label. Check the exposed area if it has rubbed against a strap as well. Even if the sunscreen is labeled water resistant, read the reapplication instructions separately.
When you get somewhere you can reapply, take off your sandals and lightly pat away sweat or moisture with a towel. If there is sand on your feet, remove it before spreading sunscreen.

As in the morning, spread it over the top of the foot, the base of the toes, and then the front of the ankle and the edges. If you change shoes for the trip home, check which areas that pair exposes. If you are also reapplying to the backs of your hands, how to apply sunscreen to the backs of your hands explains which areas to check after washing them.